logo

Technical Evaluation of Electric Motor Stator Coil Insertion, Mid-Forming, and Lacing Equipment

2026/11/17
Latest company blog about Technical Evaluation of Electric Motor Stator Coil Insertion, Mid-Forming, and Lacing Equipment
blog
Engineering Analysis of Electric Motor Stator Processing Machinery
Evaluating automated equipment for electric motor stator production requires strict alignment between mechanical tool dimensions, electrical drive capabilities, and process parameters. Key manufacturing stages—including coil insertion, mid-forming, and dual-sided lacing—demand exact physical boundaries to ensure optimal slot fill ratios and structural alignment without damaging wire enamel or slot insulation paper.
This technical document details the engineering specifications, mechanical capabilities, and technical boundaries of automated stator processing equipment manufactured by SMT Intelligent Device Manufacturing (Zhejiang) Co., Ltd., specifically focusing on models designated for coil insertion, hydraulic mid-forming, and high-speed coil lacing.
1. Automated Stator Coil Inserting Machine Parameters (Model SMT-QX16)
The coil insertion process transfers pre-wound copper or aluminum wire coils and insulation wedges into the stator slots simultaneously. The SMT-QX16 coil inserting machine integrates a specialized guide shoe array and push mechanism designed to control wire distribution under specific stack height and inner diameter parameters.
  • Stator Inner Diameter (I.D): 50-110mm
  • Stator Outer Diameter (O.D): 100-160mm
  • Maximum Stack Height: ≤160mm
  • Maximum Tooling Travel: ≤70mm
  • Applicable Wire Diameter Range: 0.2-1.2mm
Engineering Interpretation: The 0.2-1.2mm wire diameter compatibility enables the machine to process fine gauge wires for fractional horsepower appliance motors up to thicker gauge conductors used in industrial motor stators. The tooling travel capacity of ≤70mm guarantees sufficient axial push distance to move the coil end-turns cleanly through the laminated core slots, preventing wire overlap and mechanical pinching during insertion.
Automated Stator Coil Inserting Machine SMT-QX16 in factory workshop setup
Figure 1: SMT-QX16 Automatic Stator Coil Inserting Machine equipped with Delta touch panel interface and guided insertion tooling.
2. Stator Mid-Forming Hydraulic Machine Specifications (Model ZJ160)
Dual Stator Mid-Forming Machine units featuring Delta control interface
Figure 2: Model ZJ160 Stator Mid-Forming Machines with DELTA touchscreen panels in the manufacturing facility.
Following initial coil insertion, the stator coil overhang must undergo mid-forming to achieve uniform radial dimensions prior to lacing. The ZJ160 mid-forming machine utilizes internal expanders and external clamping dies driven by a hydraulic expansion cylinder to shape both end-turns.
  • Model Designation: ZJ160
  • Stator Inner Diameter (I.D.): 31 -101mm
  • Stator Outer Diameter (O.D.): ≤160mm
  • Stack Height Range: 16-100mm
  • Cylinder Displacement: ≤20F
  • Power Supply & Output: 380V/50/60Hz 3.75Kw
  • Control Hardware Interface: DELTA touchscreen PLC panel
Process Boundary & Selection Rule: The ZJ160 accommodates stack heights from 16-100mm and inner diameters between 31 -101mm. Maintaining cylinder displacement within ≤20F ensures uniform volumetric compression on the coil end-turns, preventing internal phase-to-phase insulation tearing or strand deformation.
3. Double-Sided Stator Lacing Machine Technical Metrics (Model SMT-BZ51)
Coil binding secures phase separators and slot insulation against vibration and mechanical stress. The SMT-BZ51 double-sided lacing machine utilizes a needle lacing mechanism to execute continuous stitching across both sides of the stator simultaneously.
  • Machine Model: SMT-BZ51
  • Stack Height Range: 17~100mm
  • Stator Inner Diameter (I.D): Φ25~ Φ100mm
  • Stator Outer Diameter (O.D): ≤Φ160mm
  • Maximum Overhang Height: ≤40mm
  • Stitching Cycle Speed: ≈0.6s/s
Performance Analysis: A lacing speed of approximately ≈0.6s/s provides high-throughput binding while maintaining pitch control. The overhang height limit of ≤40mm ensures that needle movement clears the copper end-turns without mechanical contact, preserving winding geometry for subsequent final forming.
SMT-BZ51 Double Sided Stator Lacing Machine in production floor
Figure 3: SMT-BZ51 Double-Sided Stator Lacing Machine installed in factory workshop.
4. Technical Specification Summary Matrix
The table below presents the verified mechanical boundaries and technical operating parameters for the evaluated stator manufacturing equipment line.
Equipment Model Process Function Dimensional Capacity (I.D / O.D / Stack) Operating & Drive Parameters
SMT-QX16 Coil Inserting Machine I.D: 50-110mm
O.D: 100-160mm
Stack Height: ≤160mm
Wire Dia: 0.2-1.2mm
Tooling Travel: ≤70mm
ZJ160 Stator Mid-Forming Machine I.D: 31 -101mm
O.D: ≤160mm
Stack Height: 16-100mm
Power: 380V/50/60Hz 3.75Kw
Displacement: ≤20F
Interface: DELTA Touchscreen
SMT-BZ51 Double-Sided Lacing Machine I.D: Φ25~ Φ100mm
O.D: ≤Φ160mm
Stack Height: 17~100mm
Lacing Speed: ≈0.6s/s
Overhang Height: ≤40mm
5. Quality Control, Factory Commissioning, and Packaging Verification
Prior to final packaging and international transport, all equipment undergoes operational validation within the designated Testing and Commissioning Area. This protocol verifies electrical continuity, sensor response time, pneumatic circuit pressure, and mechanical stroke precision under simulated motor stator production conditions.
Once inspection parameters pass verification, equipment units are encapsulated and secured inside heavy-duty wooden shipping crates to protect precision servo-hydraulic components during sea freight delivery.
Wooden shipping crates arranged in Commissioning Area
Figure 4: Prepared wooden export crates aligned in the factory's designated Commissioning Area.
Previous Post